Recent content by HooksNRounds

Left a little slack at the coax connector, just in case i have to cut and solder a new connector on in the future. Ziptied the coax in wire loom to the unused bolt holes down the channel. third brake light/license plate light wiring meets up and enters the same loom at the bottom of the...

I had a great time out there with everyone today. Hopefully next time I will be able to stay the whole weekend. Thanks Willys_ATX for "volunteering" last minute to run the beginner's group, you did great and my son and I really enjoyed running with you, pinkcamotexan, and Romac2223 (and...

You got a great deal on that gun. Battery carrier is looking good. I don't usually buy much at harbor freight, but they do have a pretty cool magnetic mig gun holder that would be great on the trail to keep your gun out of the dirt when you have to set it down. I have had a couple for quite...

Skids and Front Driveshaft -Adams 1350 front driveshaft -Evo Protek skid system

Front Bumper and Winch -Poison Spyder Brawler light front bumper with Skid -Poison Spyder Zeon winch spacers -Poison Spyder winch fairlead mount -Poison Spyder fairlead 10in. light mount -Rigid SR2 10in diffused light bar -Warn Zeon 10s -Warn power interrupt kit -Warn Zeon winch rope cover...

Cobra 29 LX CB -Cobra 29 LX -Homemade CB mount I fabbed up a mount for the CB that bolts in with the center footmans loop and curves around the plastic interior header panel. It worked out pretty good and I didn't have to cut or modify any of the interior to mount it. I thought I snapped a...

Rear Bumper and Tire Carrier -JCR Crusader mid width rear bumper -JCR Adventure tire carrier -Rotopax 2 gal gas can -Rotopax 2 gal water can -Rigid Dually 60° diffuesed lens lights installed in rear bumper -Poison Spyder Combination LED License Plate Light and 3rd Brake Light -Poison Spyder...

I ran my brake lines behind the shock as well. I installed them between the coil and shock first, but didn't like how the lines seemed to kind of get sucked into the coil when turning while checking clearance up on the jack stands.

EVO Enforcer 3" w/ King 2.0s and DL Flip Finished up installing the EVO Enforcer 3" w/ King 2.0s and drag link flip today. Also installed some ATX Cornice 17x9 wheels and some 315/70 17 Cooper STT Pro tires. Lift, drag link flip, and alignment took me about a day and a half installing it solo...

Front and Rear Bumpers I tackled getting my bumpers installed yesterday to make sure that they fit and I could get any needed modifications done before painting. I have had my eye on the Poison Spyder Brawler Lite w/ skid for quite some time while building out my build on paper before buying...

Seat Covers I did a lot of research on seat covers before pulling the trigger on the Bartact seat covers. While expensive, I really liked how well they fit and how well they have held up for people that have reviewed them. I figured these should hold up to anything that my dogs, kids, or...

Onboard Air For my onboard air setup, I went with an ARB Twin air compressor with the manifold kit. While I currently don't really need the manifold for air lockers, I figured I would go ahead and add it in now so that I could make room for it @ my mounting location for future use if I decide...

Diy spod First true mod was a DIY SPOD type relay/fuse panel. Thanks to pvanweelden's thread in the write up section, this was pretty fun and straight forward and turned out great. Daystar Switch Panel wiring: Installed switch panel: Relay/Fuse Box: I still have a little bit of cleanup...

I wanted to get a build thread started before I get to far into my build to document my progress and share my mod excitement, frustrations, successes, and failures with the community as my build progresses. All of you wonderful folks in the community have done a great job covering just about...

Hello WAL New member, but have been lurking for some time now while researching how I wanted to build up a JKU. After years of wanting a jeep, I finally pulled the trigger on a new billet JKUR last week and I am already enjoying it more than any other truck that I have owned in the past. I...