2012 Exhaust Issues with 4" Lift

zeddjb

New member
Well, I finally got the lift back on my new 2012 Jeep and low an' behold another issue arises.:grayno: I'm sure some of you have already noticed there is an issue with the exhaust and the front drive shaft coming in contact with each other at full droop.

I have seen some couplings that you can buy and add to both sides of the exhaust but that only gives you enough for a 3" lift. I myself have a 4.5" lift. Next week I'm going to take it to an exhaust shop to see what they can do.

Anyone have any fixes that worked for them or other suggestions? I would be interested to hear them.

http://www.youtube.com/watch?v=oKBlEpMaJC4&feature=player_embedded

http://zoneoffroad.com/product?ki=457&gr=-1
 

Attachments

  • 1660895_10153832265810384_1403797734_n.jpg
    1660895_10153832265810384_1403797734_n.jpg
    46.3 KB · Views: 8

2012jkfng702

New member
Check out AFE they make a replacement section for that as well.
 

Attachments

  • DSC05967.JPG
    DSC05967.JPG
    311.8 KB · Views: 3
  • IMG_8219.jpg
    IMG_8219.jpg
    105.2 KB · Views: 3

zeddjb

New member

wayoflife

Administrator
Staff member
as mentioned, you really need to replace your front drive shaft with something like a 1310 u-joint style shaft. i would also recommend that you install a set of teraflex exhaust spacers. this will help address your issues.
 

Attachments

  • 03.jpg
    03.jpg
    72.2 KB · Views: 3
  • 05.jpg
    05.jpg
    78.4 KB · Views: 3
  • 06.jpg
    06.jpg
    57.1 KB · Views: 3
  • 07.jpg
    07.jpg
    53.9 KB · Views: 1
  • ARB and sPOD.jpg
    ARB and sPOD.jpg
    71.2 KB · Views: 3
  • ARB EVO mount.jpg
    ARB EVO mount.jpg
    102.3 KB · Views: 2
  • IMG-20150127-WA0022.jpg
    IMG-20150127-WA0022.jpg
    109.5 KB · Views: 3
  • IMG-20150127-WA0025.jpg
    IMG-20150127-WA0025.jpg
    173.2 KB · Views: 3
  • IMG-20150129-WA0021.jpg
    IMG-20150129-WA0021.jpg
    89.8 KB · Views: 3

zeddjb

New member
All I can seem to find is this:

http://www.quadratec.com/products/52301_9800_07.htm


Is there a certain brand/model I should be using? Recommended?

What is the purpose of the 1310 type? I'm asking, because I'm not that knowledgeable on drive shafts. I'm guessing it's because of the angle of the front drive shaft in the rear of the shaft; the part that goes into the TC?
 

Attachments

  • 20140731_161315-2.jpg
    20140731_161315-2.jpg
    105 KB · Views: 17
  • ImageUploadedByWAYALIFE1420410228.523647.jpg
    ImageUploadedByWAYALIFE1420410228.523647.jpg
    114.3 KB · Views: 13
  • 1425426944197.jpg
    1425426944197.jpg
    81.3 KB · Views: 3
  • 1425426966506.jpg
    1425426966506.jpg
    50.3 KB · Views: 3
  • 11021219_10203536876854457_1975960406793324230_n.jpg
    11021219_10203536876854457_1975960406793324230_n.jpg
    45.3 KB · Views: 2
  • 1426437783690.jpg
    1426437783690.jpg
    85 KB · Views: 1
  • 1428938607838.jpg
    1428938607838.jpg
    171.5 KB · Views: 3
  • 1428938787602.jpg
    1428938787602.jpg
    46.7 KB · Views: 2
  • 1428938840903.jpg
    1428938840903.jpg
    306.9 KB · Views: 1

piginajeep

The Original Smartass
The 1310 JE Reel or Coast driveline will work good. The 1310's have a smaller diameter tube that helps clear the exhaust tube.
 

zeddjb

New member
The 1310 JE Reel or Coast driveline will work good. The 1310's have a smaller diameter tube that helps clear the exhaust tube.

Thanks for the info. I'm learning more and more every day.

Is the smaller diameter tube less tough than the OME shaft? I would think it would be, but maybe not? I don't want to put myself into a position that this thing is always going to break because it's smaller. (I know this is probably a dumb observation, but to someone like me who is less mechanically inclined than some others, I hope you understand the obvious questions)
 
Top Bottom