Search results

So my rear pinion bearing is going bad. I hope the dealership warranties it but doubt it with the mods and running 37 inch tires. I called 4wheel parts to get a quote to see about fixing it. They want to do a master kit so total it’s going to be about a 700 and change job. Would you recommend...

Started last night if I’m at a stop and I take off hard it starts to flash all kinds of lights on the dash. Any ideas. I’m thinking maybe loose battery cable. It doesn’t do this every time it’s sporadic. Sent from my iPhone using WAYALIFE mobile app

Sent from my iPhone using WAYALIFE mobile app

Well after getting the tires balanced I was driving away and the vibration started right away again. Drove about 5 minutes and the rear driveshaft feel off from the transfer case end. Bolts must have vibrates loose. Left this damage: Not happy at all. Shop must have not put lock tight when...

Has anyone installed factory fog lights on a quarter pounder? I have some JW Speaker fog lights and was looking at getting the EVO Quarter Pounder put really didn't want to give up these fog lights. Thanks. Sent from my SM-G955U using WAYALIFE mobile app

Started getting a pretty good vibration when I start to accelerate above 30 mph gets worse the higher speed I go till about 70 then starts to be less. I'm running 37s do have aftermarket ball joints and 1350 Driveshafts. Have not gone wheeling since I put the lift on with the upgrades. I do...

Tinted the tail lights today. Came out pretty good. Sent from my SM-G955U using WAYALIFE mobile app

Got some goodies installed. LED headlights and wating on some brackets to install the JW Speaker LED fog lights. Sent from my SM-G955U using WAYALIFE mobile app

I wanted to wire up my A-Pillar LED lights to my fog lights to use the stock fog light switch. Has anyone done this before and what did you have to do to do this? Thanks for the help. The fog lights I have are the JW Speaker LED fog lights too. Sent from my SM-G955U using WAYALIFE mobile app

The front sway bar is hitting the frame. Any thoughts on what I should do ? Don't have much room to move it over without the other side hitting the frame as well. I attached some pictures. Also I think the sway bar link is mounted incorrect on the bottom am I wrong on this? Thanks for the help...

What is the bolt size for the front sway bar links? Thanks! Sent from my SM-G955U using WAYALIFE mobile app

Got the Jeep back today and I must say I'm really impressed. Loving the Evo coilovers. Best decision if anyone is thinking about going this route. Like to thank the guys at SCL Automive for awesome work and the wife for always supporting me with my Jeep build. She's one of a kind! Sent...

Awesome thanks for the info! I'll keep everyone posted. Loving the lift so far.! Sent from my SM-G955U using WAYALIFE mobile app

Got the Jeep back today loving this lift!! Sent from my SM-G955U using WAYALIFE mobile app

Go the lift installed and at full drop the drive shaf is hitting the exhaust crossover​. Does anyone have this issue to? I have the Enforcer Pro Stage 2. What can I do? I have Adams 1350 Driveshafts. Thanks. Sent from my SM-G955U using WAYALIFE mobile app

What did people use to fill the holes on the bump stops on the spare tire carrier? Thanks. Sent from my SM-G955U using WAYALIFE mobile app

Do you need an exhaust drop spacer for a 2013 2 door when putting on the Enforcer Pro coil over system? Thanks for the help. Sent from my SM-G955U using WAYALIFE mobile app

Finally getting the Jeep back tomorrow after a week in the shop. Can't wait to take it out! Sent from my SM-G955U using WAYALIFE mobile app

Getting the rear put in finally! Almost there just need the drive shafs. Sent from my SM-G955U using WAYALIFE mobile app

New rubber!! Sent from my SM-G955U using WAYALIFE mobile app