Search results

I still have these items for sale still. They are ready to ship AEV bilstein shocks came with AEV 3.5" lift Evo tire carrier JBA headers only have been bolted on to motor before it took a dump. 5 Nitto mud grapplers 4 low tread, one with good tread 35"x 12.50 x 17 5 Mickey Thompson...

I am selling some stuff of the jeep because it is getting a new motor. LS swapped with a turbo. so I need to get rid of some stuff to get it started. and also buy a DD I am selling a Rubicon 4 to 1 transfer case I would like to get about $750 for it. SOLD Transmission is also for sale 6-speed...

Can anyone give me a rough measurement for the height of the harness slots from the floor pan?!

How much fluid does the system take? I will be running a dual pass heat sink 14" along with it

I have a few things laying around waiting for a new home. I have a trip to moab in March and looking to get a little extra money for it. Rubicon sway bar motor only. Works just replaced with evo disconnect. Hard top hoist with hand crank. I no longer have a hard top so no need for it. AEV...

I have AEV 3.5" lift coil springs for sale. Located in Flagstaff AZ. Looking to get $150 out of them. Willing to ship on your dime

So after a good look today on the jeep I noticed that my rear driveshaft actually rubs on the gas tank skid when flexed or upon up travel. It's where the driveshaft and pinion yoke join. No pictures but is there a fix to this? Also I have a nasty squeak but only when I press the brake pedal...

Ok so I have an issue I have 2 bolts that are freely rotating out of the 4 that hold on the brakes and axle shaft. Is there a fix to this? Two will come off fine but the other 2 just spin with the nut

Does anyone have the wiring instructions? I never received any directions for them. Also any tips for installing the skins?

So I am looking for D-rings now that I have my rear EVO mounts. What size and brand do you guys run? Also I have a 4 door if that helps

Is the steering box that comes with the complete kit stronger than the stock steering box? And is it a bad idea to go with sending in the stock steering box and having it made into the ram assist box? Is there any cons to it?

For some reason I can't get my Swr to a safe level. I've tried grounding the mount and the antenna but i still get way over 3, I have the teraflex cb mount. Any ideas? :thinking:

It's about time i sell some of the stuff from my build. I have a pair of 4 door rubicon rock rails (cut to fit 35"). (SOLD) VDP stubby end caps for front stock jk bumper(SOLD) AEV 3.5" lift coil springs, they were on the jeep for about 10k miles. Freedom Hard top from an 09 4 door if people...

How much in really involved in this swap? I've seen a thread on it on another forum and I'm getting tired of my six speed so I thought I would give it a shot if it's possible.

My question is, Is a 3" lift too small for long arms? Will the long arms be more of skids or will it improve off roading along with daily driving? my concern is that the will be beaten to crap on the trail with a small lift, I want to run 3" lift with 37" Trail Grapplers with stock cut fenders...

So I am in for a prorock 44 soon and I had a few questions about it. 1. Can I get away with not having the ARB locker hooked up until I get an air compressor? 2. Can I use an outer axle shaft seal? 3. Will I be able to use my current AEV drag link flip kit on this axle? For the drag link...

I have a nasty leak coming from the front passenger side axle tube. I do believe it's coming from the inner axle seal. I just replaced the ball joints which involved taking the shafts out and I believe I might have damaged one. My question is, how cheap is it to replace the seals? Would a full...

Is it possible to have the transfer case chain stretch and have it hitting the inside of the case?

I was on Instagram and saw this nifty little idea on what to do with your old honey bottles. So if you need some cups or something make some and recycle those empty bottles! Here's a link to show you how to cut the bottle http://hypervocal.com/culture/2012/how-to-cut-glass-like-walter-white/

Is there suppose to be a gap from the top of the knuckle to the bottom of the C? Here's a picture