Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: 2017 jku winter ed and 12k smitty winch in bumper

  1. #11
    Meme King WJCO's Avatar
    Join Date
    Sep 2015
    Location
    Colorado
    Posts
    25,068
    Quote Originally Posted by Primo82 View Post
    So i spoke with aev. Their mount plate for this bumper is $285 (exorbitant!) and is only rated for 10k lbs. Neither are acceptable in my book. It's not even really the money, imho. It's more the fact i can buy an entirely new bumper with a built in mountfor that price. And 10k lbs is unacceptably low load rating.

    Does anyone else have experience with internal mount plates (non-aev) on this bumper? There are so many configurations out there I'm just trying to find something that will work with my setup without too much of a headache...
    Try this thread: https://wayalife.com/showthread.php/...0A-X-HR-Bumper

    Not sure if it will work, but might give you some ideas.
    Jeep parts and accessories purchased through the following link will help support this forum and at no cost to you.
    RECOMMENDED JEEP PARTS & ACCESSORIES



    Support the JL forum: JLWRANGLER.COM

  2. #12
    Nothing but a Thing Saharaunlmtd's Avatar
    Join Date
    Feb 2013
    Location
    Pittsburgh
    Posts
    1,410

    2017 jku winter ed and 12k smitty winch in bumper

    Quote Originally Posted by Primo82 View Post
    So i spoke with aev. Their mount plate for this bumper is $285 (exorbitant!) and is only rated for 10k lbs. Neither are acceptable in my book. It's not even really the money, imho. It's more the fact i can buy an entirely new bumper with a built in mountfor that price. And 10k lbs is unacceptably low load rating.

    Does anyone else have experience with internal mount plates (non-aev) on this bumper? There are so many configurations out there I'm just trying to find something that will work with my setup without too much of a headache...
    I would pull up the instructions for AEV Part #: 10305060AB and see if there are any obvious reasons it would not work with your bumper. It's $145 at qtec.

    10k is not a low rating for JKs. I'd be surprised if more than 1% of the folks on here ran anything bigger than a 10k winch on a JKU.

    You "can" buy another bumper with a winch plate for $285 but you'd be looking at some chinese POS, IMO.
    Last edited by Saharaunlmtd; 12-07-2018 at 05:24 PM.

  3. #13
    Fresh Catch
    Join Date
    Dec 2018
    Location
    IN
    Posts
    8
    Quote Originally Posted by Saharaunlmtd View Post
    I would pull up the instructions for AEV Part #: 10305060AB and see if there are any obvious reasons it would not work with your bumper. It's $145 at qtec.

    10k is not a low rating for JKs. I'd be surprised if more than 1% of the folks on here ran anything bigger than a 10k winch on a JKU.

    You "can" buy another bumper with a winch plate for $285 but you'd be looking at some chinese POS, IMO.
    Quote Originally Posted by WJCO View Post
    Try this thread: https://wayalife.com/showthread.php/...0A-X-HR-Bumper

    Not sure if it will work, but might give you some ideas.
    Will check this out when i have time.

  4. #14
    Fresh Catch
    Join Date
    Dec 2018
    Location
    IN
    Posts
    8
    Quote Originally Posted by Saharaunlmtd View Post
    I would pull up the instructions for AEV Part #: 10305060AB and see if there are any obvious reasons it would not work with your bumper. It's $145 at qtec.

    10k is not a low rating for JKs. I'd be surprised if more than 1% of the folks on here ran anything bigger than a 10k winch on a JKU.

    You "can" buy another bumper with a winch plate for $285 but you'd be looking at some chinese POS, IMO.
    Good to know. I'll keep that in mind. A friend said if the plate is almost 300 may as well buy a bumper.

    I'll explain my "need" for a 12k lb winch. My gf is a terrible driver and owns the largest hybrid suv on the market. I live in the boonies in indiana and its winter time. She will be in a ravine by the end of winter, I'm guessing. I'd like to be qble to yank her out.

    I also burn firewood for heat. It would be awesome to be able to pull some trees out of my woods instead of having to clear a spot to dropped trees.

    Also cause why the f not?

    I know i can use a block or other methods to reduce the pull force required by the winch. But I'm trying to make sure i have more than adequate winchability.

  5. #15
    Nothing but a Thing sipafz's Avatar
    Join Date
    Mar 2015
    Location
    Saukville, Wisconsin
    Posts
    2,034
    Quote Originally Posted by Primo82 View Post
    Good to know. I'll keep that in mind. A friend said if the plate is almost 300 may as well buy a bumper.

    I'll explain my "need" for a 12k lb winch. My gf is a terrible driver and owns the largest hybrid suv on the market. I live in the boonies in indiana and its winter time. She will be in a ravine by the end of winter, I'm guessing. I'd like to be qble to yank her out.

    I also burn firewood for heat. It would be awesome to be able to pull some trees out of my woods instead of having to clear a spot to dropped trees.

    Also cause why the f not?

    I know i can use a block or other methods to reduce the pull force required by the winch. But I'm trying to make sure i have more than adequate winchability.
    The winch plate is probably rated the same as the bumper. Use a snatch block like you mentioned or buy some 7” x 2” x 3/8” channel and build your own.

  6. #16
    Fresh Catch
    Join Date
    Dec 2018
    Location
    IN
    Posts
    8
    Quote Originally Posted by sipafz View Post
    The winch plate is probably rated the same as the bumper. Use a snatch block like you mentioned or buy some 7” x 2” x 3/8” channel and build your own.
    Or maybe weld some reinforcement onto the plate?

    Honestly with a snatch block it will never see 10k. Still need to check a link or two but may install the one for 10k and mount my winch. The 10-12k smittys have the same footprint.

    From what i read the winch plate itself attaches to the frame. I may be wrong but if so the bumper rating shouldn't matter?

  7. #17
    Nothing but a Thing Saharaunlmtd's Avatar
    Join Date
    Feb 2013
    Location
    Pittsburgh
    Posts
    1,410
    Quote Originally Posted by Primo82 View Post
    Or maybe weld some reinforcement onto the plate?

    Honestly with a snatch block it will never see 10k. Still need to check a link or two but may install the one for 10k and mount my winch. The 10-12k smittys have the same footprint.

    From what i read the winch plate itself attaches to the frame. I may be wrong but if so the bumper rating shouldn't matter?
    It attaches to the frame on the bottom and the frame horn out front. This is the AEV Winch plate without the bumper.
    IMG_9256.jpg


    Sent from my iPhone using WAYALIFE mobile app

  8. #18
    Knows a Thing or Two robx251's Avatar
    Join Date
    Mar 2013
    Location
    Southern, Maine
    Posts
    640
    Quote Originally Posted by Lojo View Post
    I’m sorry it the rough country bumper. You will need a relocation bracket for brake pump.


    Sent from my iPhone using WAYALIFE mobile app
    I have the same front bumper. I’d does say that you need the relocation bracket but with some fancy eyeballs and on my smittybuilt x20 10k winch you can get away with just flipping the bushings and I painted it black to prevent oxidation


    2016 JK Rubicon
    35-12.5 R17 Radar Renegade R7 MT
    2.5 budget boost
    10k Winch/stubby bumper
    Trucklites
    TYT9800 / Pro510XL
    KC1IMA

Page 2 of 2 FirstFirst 12

Similar Threads

  1. AEV front bumper, skid plate, winch mount and non winch cover plate.
    By VeruGE*144 in forum FOR SALE (Active Members ONLY)
    Replies: 9
    Last Post: 06-11-2017, 11:39 PM
  2. Winch bumper vs winch mount on stock bumper
    By Ixion in forum Jeep JK Wrangler
    Replies: 6
    Last Post: 04-06-2017, 01:34 AM
  3. Jk front winch bumper / Winch
    By ravenmad in forum FOR SALE (Active Members ONLY)
    Replies: 6
    Last Post: 03-24-2017, 02:51 PM
  4. Smitty Built GENII 12,000 Winch W/ Synthetic Line and Fairlead (SoCal) $300.00
    By Slavens in forum FOR SALE (Active Members ONLY)
    Replies: 13
    Last Post: 05-16-2015, 09:19 PM
  5. Smitty Bilt tube bumper
    By Texasjeep01 in forum FOR SALE (Active Members ONLY)
    Replies: 0
    Last Post: 01-22-2014, 04:23 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
“wayoflife” is a moniker that I’ve been using for 20 years now and I chose it because I think it does a great job of explaining, in simple terms, the passion I have for Jeeps and the Jeep way of life. This is a lifestyle that transcends age, gender and race as the only thing you need to be a part of it is a love for the outdoors, a desire to explore, a yearning to take on a challenge and a will to conquer it. Over the years, Cindy and I have attempted to capture the essence of this lifestyle through photographs and videos and share it with others around the world. And, this is how WAYALIFE was born.
Join us
WATCH OUR VIDEOS