Jku driver side wheel straight, passenger cock-eyed.

M

Murfphy

Member
08 jku
So I have a synergy tie rod. The driver side is straight but the passenger side is not. I tighten the tie rod on the passenger side to pull the tire in.

Then adjusted the driver side. I tried to get the 1/8 toe in deal and thought I had it but it still looks a bit cockeyed.

Btw, I kinda know what I'm doing thanks to eddy write up but I do not really know what I'm doing.

If I adjust the tie rod with my wheels looking like this the drivers will turn in and the passenger may straighten out making the jeep look pigeon toed, I'm assuming.

Any ideas?
 

Attachments

  • 20190723_133928.jpg
    20190723_133928.jpg
    137.4 KB · Views: 92
  • 20190723_133932.jpg
    20190723_133932.jpg
    135 KB · Views: 93
  • 20190723_133942.jpg
    20190723_133942.jpg
    135.5 KB · Views: 93
  • 20190723_133022.jpg
    20190723_133022.jpg
    131.9 KB · Views: 93
  • 20190723_133026.jpg
    20190723_133026.jpg
    105.8 KB · Views: 92
  • 20190723_132555.jpg
    20190723_132555.jpg
    122.1 KB · Views: 88
  • 20190723_132604.jpg
    20190723_132604.jpg
    131.7 KB · Views: 89
Braxtonsag

Braxtonsag

Member
Set the toe in, then straighten the wheels, then adjust drag link to compensate for steering wheel being off

Basically back up and pull in your driveway as straight as you can. Leave the wheel sitting where it’s at. Set the toe by measuring the front and back of the front tires at the same point and once they’re straight, if your steering wheel is sideways, adjust your drag link until it’s straight.

Your tie rod adjusts toe only. Your drag link adjusts steering wheel angle only.
 
Last edited:
M

Murfphy

Member
Thank you for taking the time to reply. I know you could be doing many other things.

I'm looking at adjusting the toe in. If the drivers side wheel is straight, when I adjust the tie rod to pull the tires in....wouldnt it make the drivers side pull in to much to compensate for the cockeyed passenger side?

Or no?

I'm asking because I have been beating my head on this issue for AWHILE now.

Not rocket science but I had 4wp in oakland ca do the installation of the tie rod and other parts to find things backwards and installed incorrectly. I'm undoing their work.
 
Speedy_RCW

Speedy_RCW

Hooked
Murfphy said:
Thank you for taking the time to reply. I know you could be doing many other things.

I'm looking at adjusting the toe in. If the drivers side wheel is straight, when I adjust the tie rod to pull the tires in....wouldnt it make the drivers side pull in to much to compensate for the cockeyed passenger side?

Or no?

I'm asking because I have been beating my head on this issue for AWHILE now.

Not rocket science but I had 4wp in oakland ca do the installation of the tie rod and other parts to find things backwards and installed incorrectly. I'm undoing their work.
Click to expand...

You can't really adjust each tire independently as it seems you're thinking. Yes you may be moving one tie rod end but you're essentially moving both tires. When you shorten the tie rod length you are pulling the front of the tires in (toe in). As Braxton stated above you need to set the toe properly. Once that is done, put the wheels straight and adjust the drag link to center your steering wheel.
 
M

Murfphy

Member
Speedy_RCW said:
You can't really adjust each tire independently as it seems you're thinking. Yes you may be moving one tie rod end but you're essentially moving both tires. When you shorten the tie rod length you are pulling the front of the tires in (toe in). As Braxton stated above you need to set the toe properly. Once that is done, put the wheels straight and adjust the drag link to center your steering wheel.
Click to expand...

Solid!

Thank you guys. Its appreciated!
 
You must log in or register to reply here.
Top Bottom