What was done to your rig this week?

mattfl

mattfl

New member
JKbrick said:
Wow that is very cool, I’d love to see that print something sometime. Was this like a 3 hour deal or how long does it take?


Sent from my iPhone using WAYALIFE mobile app
Click to expand...

So the mount is in 3 pieces, both halves of the circle and then the bottom plate. Each piece took about 2 hours each to print.

Here's a time lapse of something else I printed that gives you an idea of how it works

https://www.youtube.com/watch?v=LZWFfL6LeaE

This time lapse is 51 seconds total but the total print time was about 2 hours.

Here's another time lapse, using a different piece of software that removes the movement of the extruder(the big piece in the middle that the filament comes out of)

This one is 6 seconds but the total print time was probably closer to 3 hours if I remember correctly.

https://www.youtube.com/watch?v=lBrVpVzzdG4

What I do normally is just kinda set it to print and forget about it for a few hours, or if it's a longer print, I've done 18+ hour prints, start it in the evening and let it go over night and while I'm at work the next day :)
 
7

74CJ5

New member
Put on Poison Spyder fender liners and had my crusher flares re-powder coated granite crystal. After seven years the matte black had faded and wasn’t going to look good on the new Jeep which is gloss black. IMG_1305.jpg IMG_1304.jpg


Sent from my iPhone using WAYALIFE mobile app
 
JKbrick

JKbrick

Active Member
mattfl said:
So the mount is in 3 pieces, both halves of the circle and then the bottom plate. Each piece took about 2 hours each to print.

Here's a time lapse of something else I printed that gives you an idea of how it works

https://www.youtube.com/watch?v=LZWFfL6LeaE

This time lapse is 51 seconds total but the total print time was about 2 hours.

Here's another time lapse, using a different piece of software that removes the movement of the extruder(the big piece in the middle that the filament comes out of)

This one is 6 seconds but the total print time was probably closer to 3 hours if I remember correctly.

https://www.youtube.com/watch?v=lBrVpVzzdG4

What I do normally is just kinda set it to print and forget about it for a few hours, or if it's a longer print, I've done 18+ hour prints, start it in the evening and let it go over night and while I'm at work the next day :)
Click to expand...

Holy Toledo that is very cool, thank you for posting those


Sent from my iPhone using WAYALIFE mobile app
 
World Traveler 76

World Traveler 76

New member
Swapped my Rocksport shocks and steering stabilizer over to Fox 2.0s. Maybe it’s my mind playing tricks on me, but it does feel a bit more “planted” on the road. Then again, my wallet is saying it “better” after dropping some coin and having a shop install (too cold in my garage today).

IMG_2160.jpg
IMG_2161.jpg
IMG_2163.jpg


"RUGER"
2016 Rubicon - Hard Rock
 
ammojustin

ammojustin

New member
World Traveler 76 said:
Swapped my Rocksport shocks and steering stabilizer over to Fox 2.0s. Maybe it’s my mind playing tricks on me, but it does feel a bit more “planted” on the road. Then again, my wallet is saying it “better” after dropping some coin and having a shop install (too cold in my garage today).

View attachment 315982
View attachment 315983
View attachment 315984


"RUGER"
2016 Rubicon - Hard Rock
Click to expand...

Man, those look sharp. I am in the market and I’m thinking these will be best but I don’t wheel really so I’m also thinking those might be overkill. Also considering Rubicon express. But those Fox’s look hot


Sent from my iPhone using WAYALIFE mobile app
 
You must log in or register to reply here.
Top Bottom