Cut Fender Thread

[RockyJk]

haha I wish :-/

Still need a front driveshaft, front control arms, drag link flip kit, rear track bar mount, sway bar links, and I know I am missing something :crazyeyes: :crazyeyes: :crazyeyes:

Lol always something

 

[Hobolobo]

Im not sure if ive posted mine yet, so here they are. I wanted to match the front with my bumper edges for a cleaner look.


And the side markers...

 

[sapco76]

What side markers are those?

 

[Hobolobo]

What side markers are those?

They are from o'reileys. 3/4" led. I cant remember how much they were, but they were cheap.

 

[bkac]

They are from o'reileys. 3/4" led. I cant remember how much they were, but they were cheap.

I have the same ones. Like $5-$6 each. Work great!
Just drill a 3/4" hole and push them in.

 

[MedixJK]

What side markers are those?

x3 on that. Got mine at tractor supply for a few bucks each

 

[georgi.photo]

Just finished. First DIY mod I have ever done. Hope it's good and done right.

Almost done though. A few things to clean up the look.

 

[n3tfury]

Don't think I posted in this thread. Did this a couple of weeks ago.

 

[JT2012Jk]

Did this last week

 

[ScoobyCarolanNC]

I used Eddie's write-up but with a slightly different cut on the front:
View attachment 10635 View attachment 10636

Dig it big time.

 

[OscarMike2.0]

 

[Dirt Foot]

Just finished. First DIY mod I have ever done. Hope it's good and done right.
View attachment 143417 View attachment 143418 View attachment 143419 View attachment 143420
Almost done though. A few things to clean up the look.

Time to chop that bumper!!

 

[georgi.photo]

Time to chop that bumper!!

Haha. That is in fact next. Was going to start today, but decided to brace the fenders from flapping too much at high speed. Here's what I did.

First I cut some sheet metal (pictured later) and secured it to the fender support with some pop rivets



Then, I bent the sheet metal to match the fender.



Then I put LED slim side markers (which will be wired to duo as blinkers) using the screws to secure the fender with the support via the brace.



I also added some edge trim to give it a clean look.

So... If anyone is concerned about the fenders flapping, here is a possible solution.

 

[georgi.photo]

Time to chop that bumper!!

Still waiting on the PM with the directions .

 

[n3tfury]

Haha. That is in fact next. Was going to start today, but decided to brace the fenders from flapping too much at high speed. Here's what I did.

Well done! Haven't seen that before.

Still waiting on the PM with the directions .

1) Take before pic of front bumper
2) Grab sawzall
3) Sever the bastard on both ends like it's the arms of a terrorist
4) Wipe the saliva from the corners of your mouth
5) Take after pic of front bumper

 

[Dirt Foot]

Still waiting on the PM with the directions .

PM sent. Sorry for the delay.

 

[georgi.photo]

PM sent. Sorry for the delay.

Mail received. Thanks.

 

[chester]

Looks awesome.

 

[Tachyon]

Finally trimmed the fenders! I used a utility knife and masking tape for cutting, and a hacksaw for the reinforcement trimming.

I laid out a pattern on one side, then used the trimmed piece to line up the cuts on the other side. Very simple, and it matches perfectly side to side.

Needed a new blade for every fender. Other than that, piece of cake.

 

[JEEPnGEO]

Here is mine.

This is my nephew. He wanted to show off the the little girls in his class.