Search results

Bought this tire step after having an issue on my way to Tx after the camshafts were replaced, made it to Monticello and got the engine light, and misfire; plugged in the code reader and it was codes for O2 sensors, and multiple misfire codes for the side that was worked on. Monticello was nice...

On the road, start stop first indicated battery charging and was actually operational once the battery fully charged and now after 150 MI I've got this warning Anyone come across this?

I'm about to check the control arm bushings on the JLU EVO LA, EVO instructions state to use spec torque values but I'm over the additional degree torque values. EVO also lists torque values for 9/16" bolts based on thread, pretty sure the bolts are stock metric JL bolts Those of you with EVO...

This message appeared within the week of me taking ownership of this 2020 JT. Bonus, Auto Stop/Start is disabled so no having to remember to push a button (y) (y)

Anyone have a solution for a 40% seat delete? I want to remove the driver side rear passenger and keep the 60% functional. Everything I have found so far that claims to be 40% works only with an existing 60% delete already in place.

Washed the Jeep today and while drying it off I saw several spots where the paint is bubbling because of the underlying corrosion...

2010 JKU has ABS codes C1020 Left rear speed sensor circuit; C1035 Right rear wheel sensor comparative performance. replaced the sensors but OHM tested the old against the new ones and they were all about the same. Checked the ABS plug wire for broken wire or bad connector -didn't see anything...

Been driving the JT daily on the freeway and some trips more than 30 minutes at 65+, these messages still won't clear: 1. Start/Stop Not Ready Engine Temperature Too Low (it was 75 today) 2. Start/Stop Not Ready Battery Charging 3. Aux Switches Temporarily Unavailable Battery Charging Anyone...

I've decided the JT will make a good camping platform and as I was wondering around the rabbit hole of mods to be done; I know I said I would leave it stock... did anyone really believe that? I found this made by Reaper Offroad in the USA tailgate storage box, wondering if anyone has one or...

Helping a friend install ball joints and something I don't recall is the new upper ball joint moving in/out; up/down so easily. Side to side it's tight like it should be. Once greased up it doesn't have the in/out; up/down movement. Is this normal? it's only the upper ball joints that do this...

have over 90k miles on the JLU and will be replacing the ball joints as soon, after searching for axle shaft upgrades and finding nothing for my use (spicer was months out on delivery), I had decided to replace u-joints while I had everything out. Well, thanks to Disciple Offroad and this post...

Finally got around to installing the Z-Automotive Locker bypass on the rear locker. The plug was covered with oil, means the sensor is filled with oil which I'll deal with another time. For now everything is working fine. The spot at the base is how much oil poured out when I pulled the plug...

Since Monday, 10/2/23, the radio has been locked up at every start with the following Weather & Traffic message: This locks up the radio and have to reboot it to get the message to clear and all radio functions working again. Anyone experience anything similar?

Haven't been in 4wd or used the lockers since EJS, pulled into a rest stop and got this. I have the Z-automotive locker bypass once I figure out which locker is faulty.

In 2018, purchased 5 - XD229 Machete for the JKU in 2018, total price of $1812 Was thinking about buying a set for the JLU until I saw the cost - $2980 for 5! I better get my ass in gear and clean up the ATX Chamber Pro II, found a local wheel machine shop that claims to have the machine to...

Thanks to Matt @Discount Tire! These arrived today (y)

Time for tires, was wanting to get a set of Nitto Ridge Grappler 37x12.50x17 but out of stock with no ETA available. I am considering moving up to a 38, anyone that can provide input on the Ridge Grappler 38x12.50x17 on their JLU would be appreciated. I watched the Jet video on 38's, Eddie...

I have the EVO long arm installed and the driver side upper sway bar link bolt keeps working loose The bolt fell out completely once and since then I've been keeping an eye on it and have to tighten it often. I use red locktite on it but whatever is putting pressure on it is enough to break it...

Installed the Dometic wiring harness which includes a standard 12v plug and 12v screw in plug, it's now up and out of the available storage space which I didn't like about the stock plug. What I do like about the stock plug is the fuse can be moved to become ignition switch powered which is...