What was done to your rig this week?
- Thread starter 10frank9
- Start date
JKJody
New member
Holy shit, its like you received MY order from Northridge lol. All my stuff should be here hopefully this week.
Bunz-o-fun
New member
Great Mods! assuming you have both Truck-Lites installed in the pic (they are both upper half lit, so I doubt it's the stock light on the driver side), your driver side head light looks a bit more yellow than the passenger. If you would like the color temp to match the driver and passenger side, you can shoot the retailer (or TL) an e-mail with this picture. TL will replace the head light for you. They will probably replace both.
I had this same problem two weeks ago. I sent Northridge4x4 my picture and TL sent me two new headlights - no questions asked.
Frogmech
-
OK, I am very new to this, but this ^^^ had me a bit confused. :thinking: JKS says to set to 0 +/- 5 degrees. I eyeballed the setting to get close, and then measured and its sitting at -2. :idontknow: Help a brother out if I'm missing something. That's why I'm here!
If you got what he was saying and you think I'm OK, then I'm pretty sure I'm good!
Thanks! And yes, both are installed and they are both the same color. The pic I took I was standing more to the passenger side and it was still light out so it looks off. I assure you though, both are the same brilliant color. Thanks for the info though.
Peachstatepride_
New member
Is regearing necessary to have 37s?
BlackHawk08jk
New member
Not necessary but is a very great idea to regear it will save a lot of wear and tear on your engine and trany. You will also be happy you did when you feel the power restored.
MR.Ty
Token East Coast Guy
Not necessary, but definitely nice to have. You will feel a loss of power without regearing. I just went from 3.73 to 4.88 with my 35s and it is fantastic.
Keep in mind there are other things to consider when you are going to that large if a tire.
ljvsnyder
Member
Installed center cubby hole switches.
Also made another appt (3rd appt in one year) for door water leaks. Had 1/2" water on front floor boards last rain
I know, it's just water, pull drain plugs. I would, but since it's under warranty, Jeep can make it right or ?
What did you use to make your switch panel
bigtrucker52
New member
Finally installed my Cb
RUBINOT
Caught the Bug
A friend actually made it for me. He used a thin piece of sheet metal, removed the center cubby hole insert and traced the outside edge onto the metal.
Then cut out the piece and rounded the edges. Cut two switch holes.
To fit the metal cover plate to the cubby hole insert you will have to slightly bend/roll the plate to fit the curvature of the insert.
At his recommendation I used gorilla epoxy to attach the metal plate to the cubby hole insert. Then cut off the rear 1"-2" of cubby hole insert for your wiring.
Paint, install switches and push into hole. The cubby hole insert will lock into place and hold the switch panel.
Craig.Turner
New member
Installed 4 inch RC lift with 35 inch Trail Digger MT's.
Saharaunlmtd
Caught the Bug
Rugged Ridge Snorkel installed. With having to drop the rock rail and removing my lightbar, it took 8 hours...
mudmobeeler
Caught the Bug
Set the winch on. Need to trim the bumper some. Mount it another day I guess.
10frank9
Web Wheeler
Not too bad, just grab a grinder with a flap disc and grind away. Then spray some paint to touch up and you'll be good to go.
mudmobeeler
Caught the Bug
Yeah I knew it going in. Just excited I guess and had to set it in the bumper. Was at a friends place and he wanted to see it. Lol.